Nautilus 3 Component Waterbased Finish
• For high-traffic, residential areas
• Provides long-lasting, non-ambering finish
• Available in Matte, Semi Gloss, and Gloss

NW-610 - MATTE
NW-620 - SEMI GLOSS
NW-630 - GLOSS

Technical Data:
USES: NAUTILUS 2-Component Waterbased Finish is a two-component, waterbased finish for residential and high traffic areas. NAUTILUS 2-Component Waterbased Finish provides a long-lasting, non-ambering finish for use over Precision SmoothSeal Waterbased Sealer or Precision Penetrating Seal & Stain. Available in Gloss, Semi-Gloss, and Matte.

SURFACE PREPARATION: Sand the floor according to NWFA / NOFMA specifications. Fill all cracks and holes with Precision Full Trowel Wood Filler or Precision Wood Patch. Vacuum the entire floor as well as the adjoining areas. For natural floors, final sanding should be done with 100 grit then hand sand edges with 60 or 80 grit sandpaper. Sanded floor should be tacked with a lint-free cotton cloth. Repeat until all dust is removed. Block off any direct sources of sunlight hitting the floor. Seal the floor according to label directions using Precision SmoothSeal Waterbased Finish or Precision Penetrating Seal & Stain in selected colors. All other stains should be tested for compatibility. DO NOT apply NAUTILUS 2-Component Waterbased Finish over the floors sealed with wax, non-drying oils, shellac or stearated sealers.

TIPS:
Maintain floor with routine vacuuming and Precision Wood / Laminate Floor Spray Cleaner according to directions.
Use felt floor protectors under all furniture.
DO NOT use cleaner for two weeks after final coat.
Wait 24 hours before allowing light traffic on final coat.

MIXING: Shake the finish container well before opening. Pour the finish into a clear, dry plastic container. While stirring, slowly add one bottle of NAUTILUS Crosslinker per gallon of NAUTILUS 2-Component Waterbased Finish. Continue mixing for 30 seconds after all the Crosslinker has been added. Let stand for 5 to 10 minutes before application. Only mix enough finish for application.
NOTE: Read all warnings and label copy on Crosslinker container. Use only Precision NAUTILUS Crosslinker. Never add extra amounts of Crosslinker. Never reuse crosslinked material. USE CAUTION: Crosslinker may cause skin irritation. Always wear protective gloves and clothing when handling Crosslinker.

APPLICATION: Review all MSDS for Nautilus and Nautilus Crosslinker. NAUTILUS 2-Component Waterbased Finish can be applied with a nylon brush, synthetic applicator, paint pad, or T-bar applicator at the spread rate of 450 to 550 square feet per gallon. For best results, the room and the product should be between 60ºF to 80ºF. Allow to dry at least 3 to 6 hours* or overnight before applying the next coat. Always abrade between coats.
* NOTE: Low temperatures, high humidity, as well as cool damp conditions will retard drying. Warm up area to recommended temperature or allow extra drying time.
T-BAR APPLICATION: Pour a 4" bead of material the length of the floor. Cut in the side with a paint pad. Pull the sealer in a snowplow method from end-to-end in the room. Always work with the grain of the wood. Swivel the applicator when 6" from the baseboard and stop in line with the finish bead or puddle. Rock the applicator to remove excess product then feather the turn mark. It is important to feather out all turn and stop marks. Coat the edges at the end of the room after the body of the floor. Touch up ends as you coat across the floor to feather out applicator stop marks. Edging prior to coating the field could result in picture framing (additional film). Add product as needed to maintain a uniform product bead. By changing the angle of the applicator head, the product can be repositioned to maintain a wet edge without pouring out excess material. The speed of walking during the application and the weight of the applicator can and will affect the thickness of material left on the floor. Continue this procedure across the floor and reduce the size of the bead as you near the exit from the room. When dry, abade with a used 150 grit (or finer) screen or abrasive pad with fine sandpaper strips. Be sure to hand sand all areas not reached with machine. Vacuum floor thoroughly
and tack with a lint-free cotton cloth dampened with water. Apply the next coat of NAUTILUS 2-Component Waterbased Finish. For high traffic areas, screen as above and apply additional coats (3 to 4 coats recommended). DO NOT APPLY MORE THAN 2 COATS THE SAME DAY (sealer and/or finish).

CLEAN UP: Clean applicators and equipment using soap and water.

RECOATING EXISTING FLOORS: Clean the floor with Precision Wood / Laminate Floor Spray Cleaner according to label instructions. Abrade old finish with 100 to 120 grit screen. Prepare and apply additional coats of NAUTILUS as previously instructed. Adhesion pretesting for contaminants, such as wax and oils, is recommended for all floors.

PACKAGING: Gallon 4/Case

TECHNICAL DATA
INGREDIENTS: Contains:Acrylic / urethane copolymer, glycol ethers, propylene glycol, methyl alcohol (<4%). SPECIFIC GRAVITY: 1.019 (8.5 lb/gl)
VOC: 2 lb/gl (<240 gm/l) BOILING RANGE: 192º-447ºF @ 760mmsvHG VAPOR DENSITY: Heavier than air 6.60 FLASH POINT: >200ºF
% SOLIDS: 32-34 Crosslinked Product